Soldering Tips - How to solder | Railwayscenics
Facebook
Instagram
X Formerly Twitter

Railwayscenics Soldering Hints and Tips for Beginners

soldering tips

Soldering - A beginners guide.

I have put together this guide for those who may be starting out in soldering, or those that may not have much experience with soldering, which can sometimes seem like a mysterious skill. This guide is designed to be basic and provide some assistance in learning the fundamental techniques of soldering small electronic components and projects. It is worth noting that soldering larger items, like assembling a brass locomotive kit, involves slightly different skills that are beyond the scope of this guide. In this article, I will focus on explaining the basic techniques used for soldering electrical and electronic connections. Depending on the specific task you are working on, be sure to use the appropriate type of solder and flux.

Safety.

By following these safety precautions, you can minimize risks and ensure a safe soldering experience.

Work in a Well-Ventilated Area: Soldering can produce fumes that may be harmful if inhaled. Ensure you are in a well-ventilated space, or use a fume extractor to remove any harmful vapors.

Wear Eye Protection: Soldering involves working with small, hot components and molten metal. Protect your eyes from splashes, debris, and potential soldering iron mishaps by wearing safety glasses or goggles.

Avoid Flammable Materials: Keep flammable materials, such as paper, fabric, or solvents, away from your soldering area. The heat generated by the soldering iron could ignite these materials.

Use Heat-Resistant Surfaces: Place your soldering iron on a heat-resistant mat or stand when not in use. Avoid placing it on flammable surfaces or materials that could be damaged by heat.

Mind Electrical Hazards: If you are working on live circuits, ensure proper safety precautions are taken to prevent electric shocks. Disconnect power sources and use insulated tools when necessary.

Protect Your Skin: Soldering irons can reach high temperatures and may cause burns if touched accidentally. Avoid contact with the soldering iron tip and hot components. Wear heat-resistant gloves if needed.

Handle Solder With Care: Molten solder can cause burns if it comes into contact with your skin. Be cautious when handling solder and avoid touching it directly.

Keep Workspace Organized: Cluttered workspaces increase the risk of accidents. Keep your work area clean, organized, and free from unnecessary items to prevent tripping hazards or accidental damage to components.

Check Equipment Condition: Before starting, inspect your soldering iron, solder, and other equipment for any signs of damage or wear. Faulty equipment can increase safety risks and produce poor solder joints.

Follow Manufacturers Instructions: Always follow the manufacturers instructions for your soldering equipment and materials. This includes proper usage, maintenance, and safety guidelines.

What is soldering?

Soldering is a way of joining together two or more pieces of metal. In this instance, the metal is joined together by melting an alloy, soft solder (usually made up of 40% lead and 60% tin) so that it forms a thin layer between the two surfaces. The temperature at which the solder melts depends on the amount of tin in the alloy, the more tin the lower the melting point.

How to Solder

The average beginner to railway modelling is too scared to try soldering. It is considered to be a black art, and soldering upside down is a real no no. Basic soldering is a skill that is easy to learn and not that hard to master. It just takes practice and with this practice comes confidence. The more soldering you do, the easier it will become. Honest.

Although I will focus on model railway electrical and components, the skills you will learn can be used on many projects.

Good luck, and remember....good soldering takes practice!

Soldering Tools

The only tools that are essential to enable you to solder are a soldering iron and some fluxed solder. There are however lots of other soldering accessories available which may be useful. Most modellers may have these items in their toolbox.

Different soldering jobs will require a range of different tools and equipment. Different soldering projects will require different temperatures too. For circuit board work you will need a finer tip, a lower temperature, and finer grade solder. You may also find that a magnifying glass will be beneficial. Clamps and holders are also handy when soldering cables, as are heat sinks. To wire dropper wires to code 100 track, will require a larger iron as the track will require more heat to allow soldering.

Soldering Irons

There are several things to consider when choosing a soldering iron. I do not recommend soldering guns, even though I use one, as these have no temperature control and can get too hot very quickly. This can result in damage to circuit boards, melt cable insulation, and even damaged connectors or track sleepers.

For everyday soldering a 25 or 40 watt iron with a small to medium sized bit is all that will be required. Larger bit sizes and bigger wattage irons have their place, but not for most model railway electrical joints. A larger wattage soldering iron does not mean that it is hotter, it means that it has heat to spare when working.

Wattage: It is important to remember that a higher wattage iron does not necessarily mean a hotter soldering iron. Higher wattage irons just have more power available to supply heat faster as it is absorbed by the materials being soldered. A low wattage iron may not keep its temperature on a big joint, as it can lose heat faster than it can reheat itself. Hopefully, that will make sense. Therefore, smaller joints such as circuit boards require a lesser wattage iron - around 15-30 watts will be fine. Track wire connectors need something bigger - I recommend 40 watts at least.

Temperature: There are a lot of low cost low wattage soldering irons with no temperature control available on the market today. Most of these will be perfectly fine for basic soldering, and once you find yourself doing more soldering, you may wish to purchase a better soldering iron or soldering station. If you plan on assembling white metal kits, you may also want to buy a low temperature iron specifically for this task. If you plan to assemble brass kits you will require a large soldering iron that can generate heat quickly as the brass will adsorb heat quickly.

Power: Most soldering irons are mains powered. They may operate from 230v or a reduced 12v through a transformer. Also available are battery and gas powered soldering irons and guns. These are great for the toolbox, but you would be better off using a plug in model for your workbench.

Portability: Most soldering irons will need to plug into the mains. This is fine most of the time, but if there is no mains socket around, you will need another solution. This is where gas and battery powered soldering irons can be used. They are fully portable and can be taken and used almost anywhere. They may not be as efficient at heating as a good high wattage iron, but they can get you out of trouble in an emergency. If you have a bench setup, you should consider using a soldering station. These usually have a soldering iron and de-soldering iron with heatproof stands, variable heat, and a place for a cleaning pad. A good solder station will be reliable, accurate with its temperature, and with a range of tips handy it can perform any soldering task you attempt with it.

Solder

For electrical work you should use a 60/40 tin/lead rosin core fluxed solder. Avoid solder that contains an acid flux, as this may damage the materials later if not cleaned away correctly.

Rosin, which is a naturally occurring product that comes from pine trees, core solder is available in three main types - 50/50, 60/40, and 63/37. These numbers represent the amount of tin and lead that are present in the solder. A small bit of silver is also available in some solders, which aids soldering. Solder also comes in various gauges. Solder gauge is classified just like wire gauge and AWG is used. For smaller jobs finer solder can be used as less solder will be required. In reality, any general purpose rosin core solder will be fine for most jobs on your model layout.

As everyone knows, tin/lead soldering alloys use lead. Lead has very high toxicity, As a result, lead-based solders are among the hazardous materials identified for restriction or banning by the European Unions Restriction of Hazardous Substances Directive (RoHS) and Waste Electrical and Electronic Equipment Directive (WEEE), which took effect in July 2006

The health risks associated with the use of lead meant that a new solder material was required. This led to the development of lead-free solder is also available, and works in the same way as normal lead mix solder. It also comes with cores of flux included. Lead-free solder wires should contain at least 2% flux by weight. It typically requires 15-25% higher melting temperatures than lead/tin mix alloys and does not flow so easily which means that you may need a better soldering iron to use it. Most soldering iron tips can be used with both types of solder. Removing lead-free solder is a bit more difficult, but can still be done well with practice. Lead-free solder is better for the environment and your health.

Flux

Flux is used to help clean the various oxides from the mating surfaces. It also helps the solder to flow more freely along and into the joint. Most solders now contain a flux in their core. It is always handy to have a small quantity of extra flux available. Again make sure this is a non acid based flux for electrical work. Specialist fluxes are available for lead-free solder.

Soldering Accessories and tools

Many other tools can be useful to aid good soldering available from a wide range of suppliers. You do not need them all. We have listed the main ones below.

Soldering Iron Tips

It is useful to have a small selection of manufacturers soldering iron tips available with different diameters or shapes, which can be changed depending on the type of work you intend to do. You will probably find that you become accustomed to, and work best with, a particular shape of tip.

The actual size of your soldering iron tip will make a difference to the job you are trying to do. Using a big tip on a small job will make it harder. Try to use the right size tip whenever you can. You can also get different shaped tips for different jobs. Pointed tips can be used for fine work, and blade or flat tips for more general soldering.

These are some of the different tipds that are available.

Chisel Tip: This is one of the most common types of tips and is shaped like a flat blade or chisel. Chisel tips are versatile and suitable for general soldering tasks, such as soldering wires or through-hole components on a circuit board. They provide good heat transfer and allow for precise control over the soldering process.

Conical Tip: Conical tips have a pointed end that tapers to a fine tip. These tips are useful for precision soldering work, such as soldering small surface-mount components or soldering in tight spaces where precision is required.

Bevel tip: Bevel tips have a flat surface with angled edges. They are suitable for soldering components with flat surfaces or for making fillet joints. The angled edges help in distributing heat evenly and making smooth solder joints.

Micro Tip: Micro tips are extremely small and fine, designed for soldering very small components like surface-mount devices (SMDs) or delicate electronic parts where precision and minimal heat transfer is more important.

Soldering Iron Tip Cleaners

There are several ways to keep soldering iron tips clean and in good condition. Clean tips solder better, so keeping tips clean is important.

Sponges: Sponges work very well to clean tips, but they must be kept wet. The wet sponge can dissipate quite a bit of heart so always let your soldering iron reheat before trying to solder again. I read somewhere that you should not use water to clean a tip if you are using lead-free solder, but I cannot find the article at the moment to find the reasons why.

Brass wire balls: These little brass wire balls work well and will not only clean the tip but will remove the excess solder.

Soldering Iron Stands

Iron stands are handy to use if you are doing several or more joints and wish to put the iron down whilst keeping it hot. It is much safer to use a correct stand than it is to leave a hot iron lying around where it can move and be knocked. Your partner also will not appreciate a burn mark on the dining table. Most stands consist of a heat resistant cradle for your iron to sit in, and also a space for a small sponge or tip cleaner. It is essential if you are planning to do a lot of bench soldering as it is only a matter of time before you burn something (probably your elbow resting on the hot tip) if you do not use one.

Some stands also combine a helping hands type arrangement which aids in holding and supporting your work when soldering.

Clamps

I strongly recommend clamps of some sort. Trying to hold your soldering iron, the solder, and the wire is tricky enough, but when you have to hold the connector as well it is almost impossible. There are however adjustable clamp devices, or helping hands, that can be manipulated to hold both the connector and the wire in place so you still have two free hands to apply the heat and the solder. These are cheap items and I know mine have paid for themselves many times over. Many also include a magnifying glass.

Magnifying glass

If you are doing work on PCBs (printed circuit boards) you may need to get a magnifying glass. This will help you see the tracks on the PCB, and unless you have exceptional sight, small chip resistors are pretty difficult to solder on well without a magnifying glass. They are not expensive, and some helping hands type devices come with a good magnifying glass attached.

Solder Wick

Solder wick is a fine mesh that you lie on a joint and heat. As the solder melts it is drawn out of the joint into the wick. It is usually used for cleaning up solder from tracks on a circuit board, but you will need a solder sucker to clean out the holes in the circuit board. Place the wick on the solder you want to remove then put your soldering iron on top of the wick. The wick will heat up, then the solder will melt and flow away from the joint and into the wick.

Solder Suckers

If you work on PCB's, you are going to need one of these before too long. They are a spring loaded devices designed to suck the melted solder out of a joint. They are a bit tricky to use, as you have to melt the solder with your iron, then quickly position the solder sucker over the melted solder and release the spring to suck up the solder. Better quality ones come with a metal tip rather than plastic and these should be bought as a preference.

Fume Extractors

Most solders and fluxes will give off poisonous fumes which can be harmful to skin, eyes, and lungs. A fume extractor will suck the fumes (smoke) into itself and filter them. An absolute must for your health if you are setting up a soldering bench. If you do not have the luxury of a fume extractor, ensure you solder in a well ventilated space. If you start to feel any effects of fumes please seek help.

Soldering

Let's walk through the process of creating a basic soldered wire-to-wire connection. We will explain how to join one end of a wire to another. This type of solder joint is fundamental, especially for constructing a model railway layout.

Step 1. Preparation: This may sound daft but ensure you have everything that you are going to need close at hand. You will need your soldering iron, solder, flux, wire strippers, and something to insulate the joint with after completion. I use heat shrink tube for this.

Once you are ready to begin, you will need to strip your cable. This means removing the insulation from the end of the wire and exposing the copper core. You can either use a wire stripper, side cutters, or a knife to do this. There are many types of wire strippers, and most of them work the same. You simply put the wire in, squeeze it and pull the end bit off.

Remove about 12mm (1/2 inch) of the cable insulation from the end of the wire, and then twist the fine wire strands together. This will prevent a loose wire strand from causing a short if it is left out of the bundle. Do this to both ends of the wire needing to be joined.

Step 2. Tinning: Whatever it is you are soldering, you should tin both contacts before you attempt to solder them. This coats or fills the wires or connector contacts with solder so you can easily melt them together. If the connection is dirty clean it first using files, wire wool, or scrapers. A clean surface is required for good soldering.

To tin a wire, apply the tip of your iron to the wire for a second or two then apply the solder to the wire. Do not put the solder on the iron tip as the tip will be hotter than the wire and the solder may not flow into the wire. The solder should flow freely into the wire and coat it. You may need to snip the end off afterward, particularly if you have put a little too much solder on and it has formed a little ball at the end of the wire.

Be careful not to overheat the wire, as the insulation will start to melt. On cheaper cable, the insulation can shrink back if heated too much, and expose more copper core than you intended. You can cut the wire back after you have tinned it, but it Is best simply not to overheat it.

The larger the copper core, the longer it will take to heat up enough to draw the solder in, so use a higher temperature soldering iron for larger cables if you can.

Once you have tinned both parts, you are ready to solder them together.

As I use heat shrink to protect and insulate the joint it would be best that you slide the heat shrink onto one of the wires if they have cooled. Remember it is called heat shrink for a reason, and it will shrink if the wire is too hot.

Step 3. Soldering: Before creating the soldered joint it is first necessary to create a secure strong mechanical joint. By this, I mean to twist the wires together. As I want a straight join I want to twist the wires together without forming a raised section in the wire. See images below.

As the joint should be no larger than the wires I will be using the method in the centre image. Twist the wires together and trim the end on the tinned wire if it is longer than the insulation. Place the hot tip of your iron under the wire twist for a few seconds, then carefully try melting the solder on the top of the join. Once the solder melts remove the iron from below the wire and allow the solder to run into the joint and then cool. Hold the wire steady until this has happened. You will see the solder set as it goes hard. This should all take around 1-3 seconds.

Remember that a good soldered joint will be smooth and shiny. If the joint is dull and crinkly, the wire probably moved during soldering. If you have taken too long it will have solder spikes. If it does not go so well, you may find the insulation has melted, or there is too much stripped wire showing. If this is the case, you should de-solder the joint and start again.

Once everything has cooled it should be possible to slide the heat shrink tube to cover the soldered joint. Once it is in place use the body of your soldering iron to heat the shrink material. You can also use a hot are blower, hair dryer or even a naked flame to do this. Once the tubing has shrunk, leave it cool.

You should now have a properly soldered wire connection. It may sound easier to write than to do, but with practice, it really will be this simple.

Project

Soldering wires to the bottom or outside of your rail is a very similar principle to joining two wires together. The real difference is that the two items to be soldered are of vastly different sizes. Here I find pre tinning both the stripped end of the wire and the pre cleaned place on the rail where the wire is to connect is the best method. Pre clean the rail with the aid of a fibre pencil or other means. Tin with a little solder, both the place on the rail and the wires stripped end.

To Tin - apply a small amount of solder to the cleaned irons tip, then touch the iron onto the previously cleaned area to be tinned. The solder will flow from the tip onto the area. If insufficient solder flows, keep the soldering iron tip in position, and feed more of the cored solder into the area.

Once every item has been tinned, place the wire end, which has been bent to a small L shape, up to the solder on the rail. Apply a little solder to the tip of the iron and place the iron on top of the wire and lightly press down towards the rail. The hot solder on the tip of the iron will cause both the wires solder and the rails solder to melt into one. If necessary apply a little more cored solder onto the wire with the iron still in place should there not be enough on the rail to make a solid connection. Carefully remove the iron and ensure the wire maintains in contact with the rail and does not move, waiting for 5 to 10 seconds to allow the soldered joint to cool.

The use of crocodile clips or any similar metal sprung clamps fixed onto the rails just either side of the soldering work area are advisable, as these act as mini heat sinks and help prevent the rail from being overheated away from the soldering area which can, if the heat is allowed to be transmitted along the rail, subsequently causing the plastic sleeper fixings to melt.

Clean Your Soldering Iron

Whilst soldering you should keep your soldering iron tip clean. If you get a burned looking substance on the end, you should wipe this off. This is a residue from the flux burning. You can wipe it using a special tip sponge, or a piece of tissue paper. Just remember that the tip is hot.

You should clean your soldering irons tip after use. There are many cleaning solutions and the cheapest (and some say best) is a damp sponge. Just rub the soldering iron tip on it after each solder. Another option is to use tip cleaner. This comes in a little pot that you push the tip into. This works well if your tip has not been cleaned for a while. It does create a lot of smoke, so it is better not to let the tip get so dirty that you need to use tip cleaner.

Some solder stations and holders come with a little pad at the base of the holder. If you have one of these, you should get into the habit of wiping the tip on the pad each time you apply solder with it.

Tips and Tricks

Clean Surfaces: Ensure that the surfaces to be soldered are clean and free from any dirt, grease, or oxidation. Use sandpaper, a wire brush, or a specialized cleaning solution if necessary.

Use Flux: Apply flux to the surfaces to be soldered. Flux helps improve the flow of solder and promotes better adhesion to the metal surfaces.

Heat Control: Use the right temperature for your soldering iron or gun. Too much heat can damage components or cause solder joints to become brittle, while too little heat can lead to poor solder flow.

Tinning: Pre-tin the soldering iron tip and the surfaces to be soldered. This involves melting a small amount of solder onto the tip and surfaces before joining them. Tinning helps improve heat transfer and makes soldering easier.

Proper Technique: Hold the soldering iron at the correct angle (usually 45 degrees) and apply it to the joint to heat the components evenly. Then, feed solder onto the joint, not the soldering iron tip, allowing it to melt and flow into the joint.

Use the Right Amount of Solder: Avoid using too much solder, as it can create messy joints or lead to shorts. Use just enough solder to cover the joint adequately.

Cooling: Allow the solder joint to cool naturally without moving or disturbing it. This ensures a solid, reliable connection.

Practice: Soldering is a skill that improves with practice. Start with simple projects and gradually work your way up to more complex ones to gain confidence and proficiency.

Safety: Always work in a well-ventilated area to avoid inhaling fumes from solder and flux. Wear eye protection to shield your eyes from splashes or debris.

Patience: Take your time and work methodically. Rushing can lead to mistakes and poor-quality solder joints.

Troubleshooting

Soldering can encounter several common issues, but many of these problems have straightforward solutions. Here are some potential problems when soldering and how to correct them:

Cold Joints: Cold joints occur when the solder doesnt properly flow and adhere to the components due to insufficient heat or poor soldering technique. To correct cold joints:
Ensure that the soldering iron tip is at the correct temperature for the solder being used.
Clean the components and soldering tip to ensure good thermal contact and solder flow.
Apply flux to improve solder wetting and flow.
Maintain steady contact between the soldering iron tip, components, and solder to allow proper heat transfer and solder melting.

Solder Bridges: Solder bridges happen when solder connects two adjacent conductive areas, causing a short circuit. To fix solder bridges:
Use desoldering braid or a solder sucker to remove excess solder and break the bridge.
Ensure that the soldering iron tip is clean and appropriately sized for the soldering task to avoid excess solder spreading.

Component Overheating: Excessive heat can damage sensitive electronic components, leading to malfunction or failure. To prevent component overheating:
Use a soldering iron with adjustable temperature control and set it to the lowest effective temperature.
Limit the duration of contact between the soldering iron tip and the component.
Use heat sinks or thermal clamps to dissipate heat from sensitive components during soldering.

Solder Balling: Solder balling occurs when solder forms into small balls or beads instead of adhering to the intended surface. To address solder balling:
Ensure that the soldering iron tip is clean and properly tinned.
Use the right amount of solder for the joint to prevent excess solder from forming balls.
Apply flux to promote proper solder wetting and adhesion.

Lack of Flux: Flux helps facilitate the soldering process by removing oxidation and promoting solder flow. If there's a lack of flux:
Apply additional flux to the joint using a flux pen or flux paste.
Use solder that contains flux core. If you do, then ther eis little need to add more.
Clean the components and soldering surfaces thoroughly before soldering to remove any oxidation.

Solder Splatter: Solder splatter occurs when molten solder spatters and creates unintended solder deposits on nearby components or surfaces. To avoid solder splatter:
Use the correct soldering iron tip size and shape for the soldering task.
Avoid excessive movement or agitation while soldering.
Ensure that the soldering iron tip is properly tinned and clean to prevent solder from splattering.

By identifying these common problems and applying the suggested corrective measures, you can improve the quality and reliability of your soldering work. Additionally, regular practice and proper technique will help minimize these issues over time.

Conclusion

In this article I have tried to show how simple it is to solder. When I first started all those years ago I made mistakes and still do. Try using your own methods, as I say these are only my working procedures, yours could be better who knows. All I know is that I get good results from them.

Remember the golden rules:-

  1. Clean all surfaces to be soldered
  2. Keep your iron clean
  3. Keep your sponge damp
  4. Use the correct flux
  5. Use the correct solder

Warning

At all times think safety. Do not get complacent.

All of our soldering tools can be found byclicking here.

Happy soldering!